An easy installation instruction for a 2003-2010 Toyota Land Cruiser head unit with Radio GPS DVD Player Bluetooth 3G WIFI

How can I get the most up-to-date navigation system and entertainment function in my car? The best way for you is to upgrade your old factory radio. You can not only get the anywhere by the 3D navigation system, but also can play the music and entertain your passengers. It’s also easily for you to install the new head unit. In the next part, I’d like to share an easy installation instruction for a 2003-2010 Toyota Land Cruiser head unit from Seicane with you and hope you can learn something from it.

2003-2010 Toyota Land Cruiser head unit after installation

2003-2010 Toyota Land Cruiser head unit after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2003-2010 Toyota Land Cruiser head unit installation instruction

1. Remove the panel with a lever on the both side and disconnect the wire.

1-1. Remove the panel with a lever and pull it away from dash

1-1. Remove the panel with a lever and pull it away from dash

1-2

1-2

2. Unscrew the four bolts holding the original car radio.

Unscrew the four bolts holding the original car radio

Unscrew the four bolts holding the original car radio

3. Take out the car radio and disconnect the wire harness at the back of the unit.

3-1. Take out the car radio and disconnect the wire harness at the back of the unit

3-1. Take out the car radio and disconnect the wire harness at the back of the unit

3-2

3-2

4. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

5. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

6. Connect the Seicane car radio to your original car radio ‘s plugs.

7. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t,

please check whether all the cables are connected correctly.

8. Put the new Seicane radio into the dash.

9. Put everything into their original place. All the installation is done.

 

That’s all the detailed installation instruction for a 2003-2010 Toyota Land Cruiser head unit. If you can’t understand it very well, it suggests you to the dealer or professional ask for help. If the picture shown above is different from your dashboard, please rest assured that the installation instruction is much same. Moreover, it’s important for you to check whether the new head unit can work well in your car first. If you still looking for one, I’d like to introduce a multifunctional 2003-2010 Toyota Land Cruiser head unit from Seicane to you.

http://www.seicane.com/android-touch-screen-radio-gps-sat-navi-for-2003-2010-toyota-land-cruiser-with-dvd-player-bluetooth-obd-dvr-rearview-camera-tv-usb-sd-3g-wifi-ipod-mirror-link-s166957

This multimedia 2003-2010 Toyota Land Cruiser head unit equipped with worldwide real-time navigation function of high accuracy. You can get to anywhere with this function. You can also make hand-free calls and play favorite music by Bluetooth function. Let’s enjoy the good time with it from now!

A step-by-step installation guide for a 2005-2011 Toyota YARIS head unit with Autoradio Bluetooth touch screen Mirror link OBD DVR TV USB

You will get bored and upset when the old factory radio can’t meet your needs anymore. What should you do at this moment? You can remove your old factory radio and install the new head unit in your car. It can improve your car interior environment as well as provide much convenience and enjoyment for you. Here I’d like to share a step-by-step installation guide for a 2005-2011 Toyota YARIS head unit from Seicane and you can take it as reference.

2005-2011 Toyota YARIS after installation

2005-2011 Toyota YARIS after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2005-2011 Toyota YARIS head unit installation guide

1. Using a plastic tool, carefully pry out the trim panels that surround the climate controls.

Using a plastic tool, carefully pry out the trim panels that surround the climate controls

Using a plastic tool, carefully pry out the trim panels that surround the climate controls

2. Pull out the panel with your hands with medium force.

Pull out the panel with your hands with medium force

Pull out the panel with your hands with medium force

3. Unscrew the four 10mm bolts holding the radio in place.

Unscrew the four 10mm bolts holding the radio in place

Unscrew the four 10mm bolts holding the radio in place

4. Pull the panel out and set it aside without unplugging connectors.

Pull the panel out and set it aside without unplugging connectors

Pull the panel out and set it aside without unplugging connectors

5. Pull the radio out of the dash slowly.

Pull the radio out of the dash slowly

Pull the radio out of the dash slowly

6. Disconnect the harness and antenna plug at the back of the original car radio.

Disconnect the harness and antenna plug at the back of the original car radio

Disconnect the harness and antenna plug at the back of the original car radio

7. Check all the accessories for the new Seicane car radio.

8. Connect the harnesses to the back of the new Seicane car radio.

9. Connect the Seicane car radio to your original car radio ‘s plugs.

10. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane radio into the dash.

12. Put everything into their original place. All the installation is done.

That’s all the step-by-step installation guide for a 2005-2011 Toyota YARIS head unit and wish you can learn something from that. If you find your dashboard is different from the picture shown above, please rest assured that the installation guide is much same. If you have any problem, you can go to the dealer or professionals ask for help. Moreover, you have to make sure the new head unit can work well in your car. If you are still looking for one, here is the link of a great 2005-2011 Toyota YARIS head unit from Seicane to share with you.

http://www.seicane.com/2005-2011-toyota-yaris-oem-autoradio-bluetooth-touch-screen-android-gps-navigation-system-with-bluetooth-mirror-link-obd-dvr-tv-usb-sd-3g-wifi-rearview-camera-ipod-s166221

This amazing 2005-2011 Toyota YARIS head unit is upgraded to Android 5.1.1 version which allows smoother operation and 1.6 GHz Cortex A9 Quad-core which can process the complicated database and multiple graphics in a faster way. By pairing your Bluetooth-enabled mobile phones with this unit, you can stay focused on the road ahead and keep your hands on the steering wheel control to make or receive calls for a safe driving, meanwhile, you are also allowed to stream music from your mobile phone, making your driving be filled with fun and relaxation. Wish you like it and have a good time with it!

Simple 8 steps to install a 2007-2013 TOYOTA Alphard car stereo with GPS Navigation DVD Radio Bluetooth 3G WIFI Quad-core CPU 16G Flash

Do you want to catch the trend of the new car stereo which can bring you the convenience and comfort? If you say yes, this passage is one of the important step you have to read. Here I’d like to share simple 8 steps to install a 2007-2013 TOYOTA Alphard car stereo from Seicane. If you are the car owner of TOYOTA Alphard, you can take it as reference.

2007-2013 TOYOTA Alphard car stereo after installation

2007-2013 TOYOTA Alphard car stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007-2013 TOYOTA Alphard car stereo installation guide

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6. Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8. Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane car stereo. Finally the new Seicane car stereo is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane car stereo. Finally the new Seicane car stereo is installed and a comprehensive test should be conducted on the new radio

That’s all the installation guide for a 2007-2013 TOYOTA Alphard car stereo and wish you can get some from it. If you have any questions, you can go to the dealer ask for help. Or arrange the professionals to install it directly. Besides, it’s necessary for you to look a new car stereo which can work well in your car. In here, I’d like to introduce a 2007-2013 TOYOTA Alphard car stereo from Seicane to you and wish you like it.

http://www.seicane.com/9-inch-android-gps-navigation-system-for-2007-2013-toyota-alphard-with-dvd-player-bluetooth-radio-mirror-link-multi-touch-screen-obd-dvr-rearview-camera-tv-usb-sd-3g-wifi-s169005

Want to keep the car stereo of your 2007-2013 TOYOTA Alphard in fashion? This powerful loaded with the most advanced Android 5.1.1 and the most powerful RK3188 1.6 GHz Cortex A9 Quad-core can make your dream come true. Coming with a gigantic 9 inch multi-touch screen with HD 1024*600 pixel resolution, this unit can bring you the most fantastic vision and the simplest navigation operation that you’ve never had before. While navigating, you can also listen to your favorite music by pairing your Bluetooth-enabled devices to this car stereo. You are also enabled to have more options for fun with its compatibility of a multiple audio and video formats such as DVD/VCD/CD/MP3/MPEG4/DIVX/CD-R/WMA, etc. Let’s enjoy your trips from now!

A step-by-step installation guide for a 2007-2014 Mazda CX-7 car stereo with DVD Player Mirror Link OBD DVR Bluetooth TV USB SD 3G WIFI

The car stereo is very important part in the car and you can enjoy the convenience and comfort from it. However, the old factory radio can’t meet most of your needs anymore in nowadays. It’s a best choice for you to upgrade a new car stereo. I’d like to share a step-by-step installation guide for a 2007-2014 Mazda CX-7 car stereo from Seciane. If you are the car owner of Mazda CX-7, you can take it as reference.

2007-2014 Mazda CX-7 after installation

2007-2014 Mazda CX-7 after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid

any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.Please prepare a lever and a screwdriver before the removal and the installation.

5.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007-2014 Mazda CX-7 car stereo installation guide

1. Remove the panel around the radio by using pry tool.

Remove the panel around the radio by using pry tool

Remove the panel around the radio by using pry tool

2. Remove the four screws holding in the radio.

Remove the four screws holding in the radio

Remove the four screws holding in the radio

3. Gently take the factory radio out of the dashboard.

Gently take the factory radio out of the dashboard

Gently take the factory radio out of the dashboard

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original car radio ‘s plugs.

8. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t,

please check whether all the cables are connected correctly.

9. Put the new Seicane radio into the dash.

10. Put everything into their original place.

Wish this installation guide can give you some help in the installation. If you find the picture shown above is little different from your car, please rest assured the installation guide is generic. Or you can go to the dealer or professionals ask for help.

In addition, the first thing for you to do before installation is find the suitable car stereo for your car. If you are looking for one, this wonderful 2007-2014 Mazda CX-7 car stereo from Seicane is one of the best choice for you.

http://www.seicane.com/autoradio-android-gps-navigation-system-for-2007-2014-mazda-cx-7-with-dvd-player-mirror-link-multi-touch-screen-obd-dvr-bluetooth-rear-view-camera-tv-usb-sd-3g-wifi-ipod-s167007

Specially manufactured for 2007-2014 Mazda CX-7, this in dash Android 5.1.1 GPS navigation system is an ideal car stereo to upgrade your in-car environment. A big nice 7 inch multi-touch screen with 1024*600 HD pixel resolution simplifies the navigation operation and provides a wonderful display for watching all kinds of videos. You will find it easier to reach your destination with the help of the GPS navigation. The Bluetooth pairing connectivity is available to have hands-free calls and stream music. The unit has a rearview camera input to install a backup camera to aid in parking. Wish you like it and enjoy the time with it!

How to install a 2013 2014 2015 VW Volkswagen Jetta head unit with DVD player GPS Radio Bluetooth Mirror link 3G WIFI USB SD

Installing a new multifunctional head unit in your car can give you the most up-to-date recreational function. It’s also easy for car owner to install it with a detailed installation guide. Here I’d like to share a installation guide for 2013 2014 2015 VW Volkswagen Jetta head unit from Seicane. If you are the car owner of VW Volkswagen Jetta, you can take it as reference.

2013 2014 2015 VW Volkswagen Jetta after installation

2013 2014 2015 VW Volkswagen Jetta after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2013 2014 2015 VW Volkswagen Jetta head unit installation guide

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel,

then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to

the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you

are doing this for it will affect whole procedure.

6. Put the new Seicane radio into your car, you should check whether your connections are

correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

8. Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

All above is the detailed installation guide for a 2013 2014 2015 VW Volkswagen Jetta head unit. If you have any problem with the installation, please go to the dealer or professionals ask for help. Or ask them install it directly. However, you the suitable new head unit is important for your car. If you are looking for a new one, I’d like to introduce a 2013 2014 2015 VW Volkswagen Jetta head unit from Seicane to you.

http://www.seicane.com/android-aftermarket-car-stereo-dvd-player-navigation-system-for-2013-2014-2015-vw-volkswagen-jetta-with-radio-hd-touch-screen-obd-dvr-bluetooth-mirror-link-3g-wifi-usb-sd-rear-view-camera-tv-ipod-s168011

Different from the old in-car entertainment system which only supports listening to music, this head unit for 2013 2014 2015 VW Volkswagen Jetta at present comes with comprehensive functions that are integrated with GPS navigation system, built-in Bluetooth, DVD/CD multimedia player and FM/AM radio, which enables you to be safer and have a wonderful driving experience later on. Coming with easy installation, you don’t need to make any modification or cutting to install this all-in-one head unit. It’s just plug and play!

8 easy steps to replace a 2002-2008 Dodge Stratus Viper car stereo with GPS Navigation system DVD Player Radio Touch Screen WIFI

Today I’d like to introduce how to replace a 2002-2008 Dodge Stratus Viper car stereo in 8 easy steps. You can look at the picture of dashboard in the below, it is the picture of 2002-2008 Dodge Stratus Viper after installation from Seicane. If you have the same or similar car, you can learn how to replace the car stereo by yourself. Here is the detailed installation guide.

2002-2008 Dodge Stratus Viper after installation

2002-2008 Dodge Stratus Viper after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.Please prepare a lever and a screwdriver before the removal and the installation.

5.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002-2008 Dodge Stratus Viper car stereo installation guide

1.Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2. Take the panel off the dash and disconnect the wires from the car.

2-1.Take the panel off the dash and disconnect the wires from the car

2-1.Take the panel off the dash and disconnect the wires from the car

2-2

2-2

3. Use a screw driver to remove the four screws.

Use a screw driver to remove the four screws

Use a screw driver to remove the four screws

4. Take out the unit and disconnect the wire harness at the back of the unit.

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-2

4-2

5. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane head unit

Check all the accessories for the new Seicane head unit

6. Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows.

Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows

Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows

7. Put the new unit into the dash, turn on the new unit and have a test if the new Seicane stereo is working without problem.

8. Put trim panel back on your new Seicane stereo after the normal test.

That’s the 8 easy steps to replace the 2002-2008 Dodge Stratus Viper car stereo. It’s quite easy for you to replace it by yourself. However, if you have any questions during the installation, we suggest you go to the dealer or professional ask for help. Or ask them to help you install it.

Furthermore, the suitable car stereo is very important for your car. You have to check whether the new car stereo can work well in your car. If you are looking for the new one, I have a good car stereo to introduce to you. Here is the link of 2002-2008 Dodge Stratus Viper car stereo from Seicane.

http://www.seicane.com/seicane-s09206-2002-2008-dodge-stratus-viper-android-gps-navigation-system-dvd-player-radio-touch-screen-dvr-backup-camera-tv-usb-sd-wifi-obd2-bluetooth-steering-wheel-control-1080p-video-mirror-link

The 2002-2008 Dodge Stratus Viper car stereo is a amazing car radio from Seicane. The updated GPS provides you with turn-by-turn navigation directions with the latest maps, including streets maps, displayed in a graphical format and guiding you in voice direction to help you get to the destination as well as give you the shortest route between two locations. The real-time traffic congestion maps can suggest you alternative routes to take so as to save you a lot of time. It also offers information on nearby amenities such as restaurants, fueling stations, and tourist attractions to bring you the greatest convenience!

Detailed installation instruction for a 2002-2008 Dodge Viper head unit with DVD GPS System 3D Navigation Radio RDS MP3 Rearview Camera Dual Zone AUX TV Tuner IPod USB SD

To keep your passengers entertained all the way, you can easily upgrade your factory radio with a new car radio which can support almost all the popular multimedia formats, so that you can play whatever you want to amuse your passengers. To help you install your new radio, I’d like to share a detailed installation guide about a 2002-2008 Dodge Viper head unit with you. If you have the same dashboard as the image below from Seicane, this article can help you a lot on the installation.

2002-2008 Dodge Viper head unit after installation

2002-2008 Dodge Viper head unit after installation

Please notice before the installation:    

1.Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure safety.

2.A lever and a screwdriver need to be prepared before the installation.

3.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002-2008 Dodge Viper head unit installation steps

1.Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2.Take the panel off the dash and disconnect the wires from the car.

Take the panel off the dash and disconnect the wires from the car

2-1.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

3.Remove the four screws which are holding the unit with a screwdriver.

Remove the four screws which are holding the unit with a screwdriver

Remove the four screws which are holding the unit with a screwdriver

4.Take out the unit and disconnect the wire harness at the back of the unit.

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

5.Check all the accessories for the new Seicane car radio.

5.Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original car radio ‘s plugs.

7-1. Connect the Seicane car stereo to your original car radio 's plugs

7-1. Connect the Seicane car stereo to your original car radio ‘s plugs

7-2. Connect the Seicane car stereo to your original car radio 's plugs

7-2. Connect the Seicane car stereo to your original car radio ‘s plugs

8.Put the new Seicane car radio into the dash.

9.Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10.Put trim panel back on your new Seicane car radio after the normal test.

Above all, you need to make clear about every step before you start to install this 2002-2008 Dodge Viper head unit in your car. If there is any question, you can seek help from your dealer. If you don’t have any experience on the installation, it’s strongly suggested you ask a professional to install your new unit. If you are still looking for a suitable head unit for your car, I’d like to recommend an amazing 2002-2008 Dodge Viper head unit from Seicane to you. Please click for more details:

http://www.seicane.com/hd-touch-screen-2002-2008-dodge-stratus-viper-in-dash-dvd-gps-system-3d-navigation-radio-rds-tv-tuner-ipod-usb-sd-mp3-rearview-camera-dual-zone-aux-t6015

This remarkable 2002-2008 Dodge Viper head unit comes with a large 5 inch multi-touch screen with 800*480 pixel resolution to improve the display and simplify the operation. With the Bluetooth technology, you can easily pair with your mobile phone to make and receiver hands-free calls and stream music, so that a safe and pleasant journey will be always with you. Good luck to you!

How to upgrade a 2002-2007 Jeep Liberty car stereo with OBD2 Bluetooth Mirror link Touch Screen DVR TV Video USB SD Backup Camera Steering Wheel control WIFI

A new car stereo not only can guide you to your destination with its accurate direction but also can give you much fun on the same time. Now you can easily replace your factory radio under the guidance of a detailed installation guide. The following 2002-2007 Jeep Liberty car stereo installation instruction from Seicane can be referred if you are going to replace your factory radio.

2002-2007 Jeep Liberty car stereo after installation

2002-2007 Jeep Liberty car stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002-2007 Jeep Liberty car stereo installation steps

1.Remove the trim piece above cup holder with a lever.

Remove the trim piece above cup holder with a lever

Remove the trim piece above cup holder with a lever

2.Remove 2 screws behind the trim piece.

Remove 2 screws behind the trim piece

Remove 2 screws behind the trim piece

3.Gently pry around the side of trim panel with the lever and then remove the trim panel.

Gently pry around the side of trim panel with the lever and then remove the trim panel

Gently pry around the side of trim panel with the lever and then remove the trim panel

4.Remove 4 screws which holds the factory radio in place.

Remove 4 screws which holds the factory radio in place

Remove 4 screws which holds the factory radio in place

5.Take out the factory radio.

Take out the factory radio

Take out the factory radio

6.Disconnect the smaller harness on the behind of the factory radio.

Disconnect the smaller harness on the behind of the factory radio

Disconnect the smaller harness on the behind of the factory radio

7. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car stereo to your original car radio ‘s plugs.

10.Install four screws and trim panel.

11.Install 2 screws behind the trim piece and the trim piece.

12.Turn on the new radio and have a comprehensive test if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

The step-by-step installation guide for a 2002-2007 Jeep Liberty car stereo is shown as the above. Wish you can get some help from it. If there is any question, you can consult your dealer. However, if you can’t finish it on your own, you’d better ask a professional for help. If you are still looking for an ideal car stereo for your car, you can refer to this amazing 2002-2007 Jeep Liberty car stereo from Seicane. Please click for more details:

http://www.seicane.com/seicane-s09201-android-dvd-radio-gps-navigation-system-for-2002-2007-jeep-liberty-with-obd2-bluetooth-mirror-link-touch-screen-dvr-tv-video-usb-sd-backup-camera-steering-wheel-control-wifi

With a large 4.3 inch HD multi-touch screen to provide the great display which is as same as the real images , this intelligent car stereo can replace your factory radio without any gap in your Jeep Liberty. Its remarkable GPS navigation system can offer your current location, route planning, turn-by-turn direction and voice prompts to guide you to a wide range of locations. You can also play DVD, CD, TV, Bluetooth music, iPod, FM/AM radio on the way for relaxation and pleasure.

How to easily upgrade a 2003 2004 2005 2006 Jeep Wrangler car radio with Bluetooth Music MP3 AUX Rearview Camera TV IPOD IPhone USB SD

With a step-by-step installation guide, some car owners can install a new car stereo in their car, while some may not. If you don’t have any experience on the installation, it maybe quite hard for you. In that case, you can turn to a professional for help. If you are a car owner of a 2003 2004 2005 2006 Jeep Wrangler, this 2003 2004 2005 2006 Jeep Wrangler car radio installation guide can be much helpful for you.

2003 2004 2005 2006 Jeep Wrangler car radio after installation

2003 2004 2005 2006 Jeep Wrangler car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2003 2004 2005 2006 Jeep Wrangler car radio installation steps

1.Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2.Take the panel off the dash and disconnect the wires from the car.

2-1.Take the panel off the dash and disconnect the wires from the car

2-1.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

3.Remove the four screws which are holding the unit with a screwdriver.

Remove the four screws which are holding the unit with a screwdriver

Remove the four screws which are holding the unit with a screwdriver

4.Take out the unit and disconnect the wire harness at the back of the unit.

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

5.Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original car radio ‘s plugs.

7-1. Connect the Seicane car stereo to your original car radio 's plugs

7-1. Connect the Seicane car stereo to your original car radio ‘s plugs

7-2. Connect the Seicane car stereo to your original car radio 's plugs

7-2. Connect the Seicane car stereo to your original car radio ‘s plugs

8.Put the new Seicane car radio into the dash.

9.Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10.Put trim panel back on your new Seicane car radio after the normal test.

To make your upgrade successful, firstly, you need to pick up a right aftermarket radio for your car. If you are unsure which radio can fit your car, you can click the following link which is about an amazing 2003 2004 2005 2006 Jeep Wrangler car radio from Seicane and take it as a reference.

http://www.seicane.com/aftermarket-radio-gps-dvd-player-for-2002-2007-jeep-grand-cherokee-liberty-patriot-wrangler-with-bluetooth-music-tv-ipod-iphone-usb-sd-mp3-aux-rearview-camera-t6015

With this Jeep Wrangler car radio in your car, you are able to stay focused on the road ahead and keep your hands on the steering wheel to dial, receive, reject or mute the phone calls when you simply sync your compatible mobile phone with this unit via the Bluetooth connectivity. You can watch you favorite movies in your car to relax when you are outsides. To have a more relaxing trip on the way, this Jeep Wrangler car radio is just your great choice! Good luck to you!

Easy installation steps to install a 2002-2007 Jeep Liberty car stereo with TV Bluetooth Backup Camera USB SD MP3 MP5 IPOD AUX MP3

Now more and more and car owners want to get more convenience and enjoyment on the way, so they try to upgrade the factory radio with a new aftermarket car stereo. If you also have such a plan, it’s wise of you to find a detailed installation guide. Now I’d like to introduce a step-by-step 2002-2007 Jeep Liberty car stereo installation guide from Seicane. You can read it carefully to help with the installation.

2002-2007 Jeep Liberty car stereo after installation

2002-2007 Jeep Liberty car stereo after installation

Please notice before the installation:    

1.Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure safety.

2.A lever and a screwdriver need to be prepared before the installation.

3.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002-2007 Jeep Liberty car stereo installation steps

1.Remove the trim piece above cup holder with a lever.

Remove the trim piece above cup holder with a lever

Remove the trim piece above cup holder with a lever

2.Remove 2 screws behind the trim piece.

Remove 2 screws behind the trim piece

Remove 2 screws behind the trim piece

3.Gently pry around the side of trim panel with the lever and then remove the trim panel.

Gently pry around the side of trim panel with the lever and then remove the trim panel

Gently pry around the side of trim panel with the lever and then remove the trim panel

4.Remove 4 screws which holds the factory radio in place.

Remove 4 screws which holds the factory radio in place

Remove 4 screws which holds the factory radio in place

5.Take out the original radio.

Take out the factory radio

Take out the factory radio

6.Disconnect the smaller harness on the behind of the original car radio.

Disconnect the smaller harness on the behind of the factory radio

Disconnect the smaller harness on the behind of the factory radio

7. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9.Connect the Seicane car stereo to your original car radio ‘s plugs.

10.Install four screws and trim panel.

11.Install 2 screws behind the trim piece and the trim piece.

12.Turn on the new radio and have a comprehensive test if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Now can you install your new radio in you car under the guidance of this detailed installation guide specially for a 2002-2007 Jeep Liberty car stereo? If not, don’t worry, you can ask a professional for help. If there is any question, you can consult your dealer. But if you don’t have an ideal radio for your car, I’d like to recommend this advanced 2002-2007 Jeep Liberty car stereo from Seicane to you. Here’s the link, please check out the following link for more details:

http://www.seicane.com/cheap-2002-2003-2004-2007-jeep-wrangler-liberty-in-dash-radio-gps-sat-nav-stereo-cd-dvd-player-tv-bluetooth-backup-camera-usb-sd-mp3-mp5-ipod-aux-mp3-t6096

This Jeep Liberty car stereo is equipped with a great WinCE 6.0 system to smooth the operation. You can easily operate on the large 4.3-inch multi-touch screen with 800*480 pixel resolution. It’s completely plug and play and easy to install, you don’t have to modify or cut any wire in your car to achieve the installation. You can also enjoy many other features in your car. Wish you like it and have a great time with it!