1,392 views

Simple 8 steps to install a 2007-2013 TOYOTA Alphard car stereo with GPS Navigation DVD Radio Bluetooth 3G WIFI Quad-core CPU 16G Flash

Do you want to catch the trend of the new car stereo which can bring you the convenience and comfort? If you say yes, this passage is one of the important step you have to read. Here I’d like to share simple 8 steps to install a 2007-2013 TOYOTA Alphard car stereo from Seicane. If you are the car owner of TOYOTA Alphard, you can take it as reference.

2007-2013 TOYOTA Alphard car stereo after installation

2007-2013 TOYOTA Alphard car stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007-2013 TOYOTA Alphard car stereo installation guide

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6. Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8. Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane car stereo. Finally the new Seicane car stereo is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane car stereo. Finally the new Seicane car stereo is installed and a comprehensive test should be conducted on the new radio

That’s all the installation guide for a 2007-2013 TOYOTA Alphard car stereo and wish you can get some from it. If you have any questions, you can go to the dealer ask for help. Or arrange the professionals to install it directly. Besides, it’s necessary for you to look a new car stereo which can work well in your car. In here, I’d like to introduce a 2007-2013 TOYOTA Alphard car stereo from Seicane to you and wish you like it.

http://www.seicane.com/9-inch-android-gps-navigation-system-for-2007-2013-toyota-alphard-with-dvd-player-bluetooth-radio-mirror-link-multi-touch-screen-obd-dvr-rearview-camera-tv-usb-sd-3g-wifi-s169005

Want to keep the car stereo of your 2007-2013 TOYOTA Alphard in fashion? This powerful loaded with the most advanced Android 5.1.1 and the most powerful RK3188 1.6 GHz Cortex A9 Quad-core can make your dream come true. Coming with a gigantic 9 inch multi-touch screen with HD 1024*600 pixel resolution, this unit can bring you the most fantastic vision and the simplest navigation operation that you’ve never had before. While navigating, you can also listen to your favorite music by pairing your Bluetooth-enabled devices to this car stereo. You are also enabled to have more options for fun with its compatibility of a multiple audio and video formats such as DVD/VCD/CD/MP3/MPEG4/DIVX/CD-R/WMA, etc. Let’s enjoy your trips from now!

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *