When you are driving around an unfamiliar location, with a worldwide real-time GPS navigation system, you can reach your ideal destinations without getting lost any longer. However, your factory radio may not be compatible with GPS navigation function or its GPS function is not powerful enough. Under this circumstance, you can easily replace it with a modern multifunctional car radio. If you own a 2007 2008 2009 2010 2011-2013 FIAT Fiorino and plan to install a new car radio, you can refer to the following installation steps from Seicane special for a 2007 2008 2009 2010 2011-2013 FIAT Fiorino car radio.
Before and during installation, you should notice:
1.Before connecting, please make sure the ignition is off to avoid short circuit.
2.Ensure connect the yellow and red power cable at last.
3.Ensure that all loose wires are isolated with electrical tape
4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5.Ensure that all ground is connected to the same place.
6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400
2007 2008 2009 2010 2011-2013 FIAT Fiorino car radio installation steps
1. The original car radio.
2. Insert the release keys in the slots of the original radio.
3. Pull outwards to remove the original radio.
4. Disconnect the connectors and cables behind to release the original radio.
5. Use a plastic removal tool to pry the cover and then release it.
6. Check all the accessories for the new Seicane car radio.
7. Connect the harnesses to the back of the new Seicane car radio.
8. Connect the Seicane car stereo to your original stereo’s plugs.
9. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
10. Put the new Seicane car stereo into the dash.
11. Put everything into their original place. All the installation is done.
Don’t be over worried if you encounter any problems before or during the installation. Just calm down firstly, and then consult your dealer, communicate with someone experienced or seek help from a professional. If you still think it hard for you to remove the factory radio and install the new car radio, you can directly go to a car radio upgrade center to have the new car radio installed by a professional technician. Anyway, it is very essential for you to select an ideal car radio before the installation. If you don’t have any ideas, I’d like to recommend a remarkable 2007 2008 2009 2010 2011-2013 FIAT Fiorino car radio from Seicane to you. Here comes the related link, please click:
This car radio loaded with the stable Android 6.0 operation system, an 8-core 1.5 GHz Coretex-A53 processor and 32GB INand flah as well as 2GB RAM, can be the best replacement for your factory radio in a 2007 2008 2009 2010 2011-2013 FIAT Fiorino.
With this car radio installed in your car, you can take advantage of a lot of basic features, mainly including worldwide 3D GPS navigation, FM/AM radio, Bluetooth hands-free calls, Bluetooth streaming music, steering wheel control, USB/SD card connection, etc. Apart from these basic features, you can add some optional functions like digital TV, car DVR, OBD2, DAB, TPMS, etc to this car radio according to your preference and your requirements.
With the assistance of the high-end 3D GPS navigation system, you are able to locate where you are and navigate to your ideal destinations through turn-by-turn directions and voice prompts. And its dual zone function enables you to enjoy your favorite music while navigating.
Thanks for reading and wish you have a wonderful driving experience. If you like this unit, just add it to your shopping cart. Good luck!